The Parts Drop

Parts, Supplies & Information for Xerox®
Copiers, Printers, & Fax Machines.

  Navigation:
  Home » Tech Info
Not Logged In
(Retail)...
   |  Log In  |  Your Account  |  Your Cart  |  Checkout  
website security
Catalog more
- Main Catalog Menu
Part Search
Choose Your Model#
(Optional) Narrows your search to a specific style of machine.
Enter Keywords
You can include a full model name,and a part# (if you have it), as well as descriptive keywords.
 
Tech Info
- Tech Info Menu
(codes & diagnostics)
Your Order more
0 items
Information
Shipping & Returns
Privacy Notice
Conditions of Use
View All Products
Contact Us

Important:.. the information presented here is for the use of a qualified, experienced technician. Without the background knowledge which comes with training, you risk doing more damage than good to the copier & also risk your own safety.
If you are not willing to take 100% responsibility for your actions, do not use the information posted here. Thank you. Read our Conditions of Use for more information


    
5312 style TECH INFO
5312,5313,5314
1012 style Copier
These model #’s are trademarks of Xerox Corporation.
All of this information plus far more detailed procedures and parts lists
can be found in their Service Manual. This is available for sale on their website at www.xdss.com

These models as well as many other makes and models are also covered in Intravia's Guides 6th Edition.

Status Codes:
Tray 3 Lamp Flashing = Bypass Feed problem.
C1 Tray 1 misfeed (paper leaving didn’t reach the Registration Gate Sensor in time)
C2 Tray 2 misfeed
E1 Exit sensor jam (paper didn’t reach the Exit Switch in time or paper is sitting on the Registration Gate Sensor during standby)
E3 Exit sensor jam (paper did not leave the Exit Switch in time or paper is sitting on the Exit Switch during standby)
E6 Paper tray cover interlock is open.
J1 Low Toner.
J3 No copy cartridge installed.
J7 Copy Cartridge has reached ‘end of life’.
J8 Wrong Copy Cartridge.
L6 Auditron or other attached accessory is not enabled.
U1 Main Motor problem (Main Board didn’t sense clock signals from Main Motor during copy cycle)
U2 Scan problem (Main Board sensed that the lamp carriage did not scan properly)
U3 Lens problem (Main Board didn’t sense that the lens moved at the proper time)
U4* Fuser took too long to warm up,
or: Fuser overheat,
or: Open Thermistor, Lamp or Thermal Fuse.
U6 Main Board problem (Main Board sensed an EPROM read/write error)
U8 Exposure problem (Main Board sensed that the Exposure Sensor didn’t detect light from the Exposure Lamp during the copy cycle)

Diagnostics:
To enter diagnostics: Turn on the copier while holding the ‘0’ button...all control panel lamps will light.
To enter a code: Enter the first part of the code followed by the 'Start' button, then the second part of the code followed by the 'Start' button again.
Note: If an invalid code is entered, ‘Er’ is displayed. Press 'Stop' and enter a new code.

*To clear a fuser code: Enter diagnostics, enter ‘52’ followed by ‘Start’. If a fuser code is current, the number '1' will flash, enter ‘0’ to clear the code followed by ‘Start’ to lock in your selection. Press ‘Stop’ and then you can shut down.

Checking the Total Copy Count: When the copier is at ready, press the ‘0’ button and hold for at least 6 seconds...’cc’ will be displayed followed by six digits (two digits at a time, for about 2 second intervals) followed at the end by ‘cc’ again. (ie: cc 01 23 45 cc would indicate 12,345 copies). Checking the Drum Cartridge (CRU) Count: When the copier is at ready, press the ‘Stop’ button and hold it for at least 6 seconds... the number displayed x1000 is the cartridge count (rounded to the nearest 1000 copies).

To run the copier with jam detection off or without paper (Jam Bypass): Press ‘2’ while turning on power... When the copier comes to ‘Ready’, use Tray 1... All status codes will work except the paper jam codes (C1,C2,E1,E3). To exit this mode, turn off the copier.

Testing Switches & Sensors: (Input Component Codes) In diagnostic mode, enter the code for the component, press ‘Start’, then manually actuate the switch or sensor and watch for the Ready Lamp to turn on & off.
Code Component
5 Tray 2 presence
6 SWI-1 (Dipswitch 1 on Main Board)
7 SWI-2 (Dipswitch 2 on Main Board)
8 SWI-3 (Dipswitch 3 on Main Board)
9 SWI-4 (Dipswitch 4 on Main Board)
60 Optics Registration Sensor
63 Lens Sensor
70 Tray 1 & 2 Access Cover Interlock Switches
82 Registration Gate Sensor
83 Exit Switch
84 Paper Size Sensor
88 Manual Feed Sensor
94 Low Toner Sensor

Checking Clutches, Motors, Lamps, Solenoids & Corotrons: (Output Component Codes)
Use these codes to test a component such as a clutch or motor. Enter the code followed by ‘Start’ to activate a component. Most components will activate for 1 second (the Exposure lamp will light for 30 seconds).
Code Component
11 Optics Motor (2 motors on the 5314)
41 Main Motor & Erase Lamp
61 Scan Drive Motor (Forward)
62 Scan Drive Motor (Reverse)
64 Lens / Mirror Solenoid
66 Exposure Lamp
80 Tray 1 Feed Solenoid
81 Tray 2 Feed Solenoid
85 Registration Gate Solenoid
86 Nudger Solenoid
87 Paddle Solenoid
89 Billing Meter
90 Corotron & Bias HVPS (Normal Mode)
91 Corotron & Bias HVPS (Photo Mode)
92 Interimage / Edge Erase Lamp

Changing NVM Settings: (Non Volatile Memory Settings)
Use these entry codes to read & alter settings for machine performance. To change a setting... enter the diagnostic code you want, press ‘Start’ (the current setting will be displayed). Enter the new value followed by ‘Start’ and then ‘Stop’.
Code Setting Description Range Default Details
20 Lead Edge Registration 0 to 64 32 1 step = approx. 0.167mm
21* Exposure (100%)
Exposure (Reduction)
Exposure (Enlargement)
0 to 64
0 to 64
0 to 64
32
32
32
Higher setting means more voltage to the Exposure Lamp and lighter copies.
22 Fuser Temperature(Standby) 0 to 64 32 Fuser temp. in Standby Mode
23 Fuser Temperature (Copy Cycle) 0 to 64 32 Sets Fuser Temperature during the Copy Cycle.
24 Lead Edge Erase 0 to 64 32 1 Step = 0.17 mm
25 Trail Edge Erase 0 to 64 32 1 Step = 1.05 mm
26 Vertical Magnification 0 to 19 &
27 to 64
32 1 Step = 0.1% Note: Range of 20 to 26 causes U2 codes.
27 Horizontal Magnification 0 to 64 32 1 Step = 0.1%
28** White Level Reference Setting - - -
29 White Level Reference Value (Auto Mode only) 0 to 64 32 Manually changes the White Reference Value.
51 Accessory 0 or 1 0 0=Inhibit , 1=Enable
52 Fuser Overheat Clear 0 or 1 0 0=Clear overheat , 1=U4 Code

*Setting the Exposure Levels: Put the Exposure Lever at the center position, turn off the ‘Auto Exposure’, and select 100% magnification. Enter Diagnostic Code ‘21’. Press the ‘Start’ button, the copier will make 10 copies. Adjust the exposure during the copy cycle by pressing the ‘5’ to increase, or the ‘0’ to decrease the exposure. Repeat this process in 64% magnification & 129% magnification.
If this process doesn’t give you enough of a handle, VR1 on the Main Board (under the Upper Rear Cover) is the coarse adjustment. Set the exposure level at 32 using the procedure above. Then turn VR1 (clockwise increases exposure).

** Setting the White Level Reference Value: Enter Diagnostic Code ‘28’. Cover the entire Document Glass with plain white paper & close the Platen Cover. Press ‘Start’, the display will show ‘bb’. Select 100% and press ‘Start’. One copy will be made and the white reference Correction Value is stored in memory. The copier leaves diagnostic mode. Then go back into diagnostic mode & enter code ‘29’ followed by ‘Start’. Add 11 to the value displayed and enter that new value. Press ‘Start’ to lock in the new value.

Main PWB Dip Switch settings:
SWITCH #: 1 2 3 4
U.S.:
5312 ON OFF ON OFF
5313 ON OFF OFF OFF
5314 ON OFF OFF ON
Rank (European):
5312 OFF ON ON OFF
5313 OFF ON OFF OFF
5314 OFF ON OFF ON
Example: US 5312:
U.S. 5312 Dip Switch Settings

SPECIFICATIONS:
5312,5313,5314
Model# 1stCopy Speed Warmup Capacity
(#sheets)
Dim&wt
(round up)
Power
5312 9sec. 12cpm 20sec. 250
bypass:50
20x19x12
73lbs
115v,15a
5313 9sec. 12cpm 20sec. 250
bypass:50
20x19x12
73lbs
115v,15a
5314 9sec. 12cpm 20sec. 250
bypass:50
22x23x16
80lbs
115v,15a

Suggested Retail Pricing: 5312: $2,800.- ... 5314: $3,425.-

5313 Zoom Capabilities
(Preset Reduction = 64,78%) (Preset Enlargement = 110,129%)
(Zoom Magnification = 64-129%...1% increments)
5314 Zoom Capabilities
(Preset Reduction = 64,78%) (Preset Enlargement = 129,154%)
(Zoom Magnification = 50-200%...1% increments)

Yields:
Drum Cartridge: 18,000
Toner Cartridge: 4,000 (Assumes average area coverage of 6%...Regular full page of text)

To Program your copier to your preferences:

  • Press the ‘Auto’ button for about 6 seconds. The copier diagram lights will flash.
  • Enter the 'Program Number' followed by ‘Start’. The current setting will be displayed (Default for all of the Programs is ‘1’).
  • Enter your choice from the available Program Options and press ‘Start’. Press ‘Auto’ to exit the Programming Mode.
If you want to change the Paper Tray your machine uses by default:
The 'Program Number' is ‘20’.
The options are: 1 = Tray 1... 2 = Tray 2... 3 = Bypass Tray
Turning the 'Auto Clear' function On & Off:
(Note: Auto Clear must be On for the Power Saver function to work).
The 'Program Number' is ‘21’.
The options are: 0 = Off (Disabled)... 1 = On (Enabled)...
Turning the 'Power Saver' function On & Off:
(Note: Auto Clear must be ‘on’ for the Power Saver function to work).
Power Saver causes the machine to go to a lower level of readiness. It displays ‘--’ 4 minutes after the last copy is made...you can press any key to return to Standby Mode.
The 'Program Number' is ‘24’.
The options are: 0 = Off (Disabled)... 1 = On (Enabled)
Selecting an alternative default magnification:
The 'Program Number' is ‘25’.
Your options are: 1 = 100%... 2 = 64%... 3 = 78%... 4 = 129%... 5 = 154%
To turn the 'Auto Contrast' option on and off:
The 'Program Number' is ‘45’.
Your options are: 0 = Off (Disabled)... 1 = On (Enabled)


www.partsdrop.com (201)387-7776 U.S.A.
The Parts Drop is a family owned business. Our home is at 26 Palisade Avenue in Bergenfield, NJ 07621.
Thank you for your business!

* Xerox and all of their model #'s are Registered Trademarks of Xerox Corporation...
The Parts Drop is not affiliated with Xerox Corporation except for the fact that we love'em!

This Website layout was created based on the wonderful: osCommerce
Powered by osCommerce Copyright © 2003-2008


Olla Cart