Intravia’s Guides covers these models as well as many other makes and models in the 6th Edition.

Status Codes:

Tray 3 Lamp Flashing = Bypass Feed problem.

C1	Tray 1 misfeed (paper leaving didn’t reach the Registration Gate Sensor in time)
C2	Tray 2 misfeed
E1	Exit sensor jam (paper didn’t reach the Exit Switch in time or paper is sitting on the Registration Gate Sensor during standby)
E3	Exit sensor jam (paper did not leave the Exit Switch in time or paper is sitting on the Exit Switch during standby)
E6	Paper tray cover interlock is open.
J1	Low Toner.
J3	No copy cartridge installed.
J7	Copy Cartridge has reached ‘end of life’.
J8	Wrong Copy Cartridge.
L6	Auditron or other attached accessory is not enabled.
U1	Main Motor problem (Main Board didn’t sense clock signals from Main Motor during copy cycle)
U2	Scan problem (Main Board sensed that the lamp carriage did not scan properly)
U3	Lens problem (Main Board didn’t sense that the lens moved at the proper time)
U4*	Fuser took too long to warm up, or: Fuser overheat, or: Open Thermistor, Lamp or Thermal Fuse.
U6	Main Board problem (Main Board sensed an EPROM read/write error)
U8	Exposure problem (Main Board sensed that the Exposure Sensor didn’t detect light from the Exposure Lamp during the copy cycle)

Diagnostics:
To enter diagnostics: Turn on the copier while holding the ‘0’ button...all control panel lamps will light.
To enter a code: Enter the first part of the code followed by the 'Start' button, then the second part of the code followed by the 'Start' button again.
Note: If an invalid code is entered, ‘Er’ is displayed. Press 'Stop' and enter a new code.

*To clear a fuser code: Enter diagnostics, enter ‘52’ followed by ‘Start’. If a fuser code is current, the number '1' will flash, enter ‘0’ to clear the code followed by ‘Start’ to lock in your selection. Press ‘Stop’ and then you can shut down.

Checking the Total Copy Count: When the copier is at ready, press the ‘0’ button and hold for at least 6 seconds...’cc’ will be displayed followed by six digits (two digits at a time, for about 2 second intervals) followed at the end by ‘cc’ again. (ie: cc 01 23 45 cc would indicate 12,345 copies). Checking the Drum Cartridge (CRU) Count: When the copier is at ready, press the ‘Stop’ button and hold it for at least 6 seconds... the number displayed x1000 is the cartridge count (rounded to the nearest 1000 copies).

To run the copier with jam detection off or without paper (Jam Bypass): Press ‘2’ while turning on power... When the copier comes to ‘Ready’, use Tray 1... All status codes will work except the paper jam codes (C1,C2,E1,E3). To exit this mode, turn off the copier.

Testing Switches & Sensors: (Input Component Codes) In diagnostic mode, enter the code for the component, press ‘Start’, then manually actuate the switch or sensor and watch for the Ready Lamp to turn on & off. Code Component 5 Tray 2 presence 6 SWI-1 (Dipswitch 1 on Main Board) 7 SWI-2 (Dipswitch 2 on Main Board) 8 SWI-3 (Dipswitch 3 on Main Board) 9 SWI-4 (Dipswitch 4 on Main Board) 60 Optics Registration Sensor 63 Lens Sensor 70 Tray 1 & 2 Access Cover Interlock Switches 82 Registration Gate Sensor 83 Exit Switch 84 Paper Size Sensor 88 Manual Feed Sensor 94 Low Toner Sensor

Checking Clutches, Motors, Lamps, Solenoids & Corotrons: (Output Component Codes) Use these codes to test a component such as a clutch or motor. Enter the code followed by ‘Start’ to activate a component. Most components will activate for 1 second (the Exposure lamp will light for 30 seconds). Code Component 11 Optics Motor (2 motors on the 5314) 41 Main Motor & Erase Lamp 61 Scan Drive Motor (Forward) 62 Scan Drive Motor (Reverse) 64 Lens / Mirror Solenoid 66 Exposure Lamp 80 Tray 1 Feed Solenoid 81 Tray 2 Feed Solenoid 85 Registration Gate Solenoid 86 Nudger Solenoid 87 Paddle Solenoid 89 Billing Meter 90 Corotron & Bias HVPS (Normal Mode) 91 Corotron & Bias HVPS (Photo Mode) 92 Interimage / Edge Erase Lamp

Changing NVM Settings: (Non Volatile Memory Settings) Use these entry codes to read & alter settings for machine performance. To change a setting... enter the diagnostic code you want, press ‘Start’ (the current setting will be displayed). Enter the new value followed by ‘Start’ and then ‘Stop’. Code Setting Description Range Default Details 20 Lead Edge Registration 0 to 64 32 1 step = approx. 0.167mm 21* Exposure (100%) Exposure (Reduction) Exposure (Enlargement) 0 to 64 0 to 64 0 to 64 32 32 32 Higher setting means more voltage to the Exposure Lamp and lighter copies. 22 Fuser Temperature(Standby) 0 to 64 32 Fuser temp. in Standby Mode 23 Fuser Temperature (Copy Cycle) 0 to 64 32 Sets Fuser Temperature during the Copy Cycle. 24 Lead Edge Erase 0 to 64 32 1 Step = 0.17 mm 25 Trail Edge Erase 0 to 64 32 1 Step = 1.05 mm 26 Vertical Magnification 0 to 19 & 27 to 64 32 1 Step = 0.1% Note: Range of 20 to 26 causes U2 codes. 27 Horizontal Magnification 0 to 64 32 1 Step = 0.1% 28** White Level Reference Setting - - - 29 White Level Reference Value (Auto Mode only) 0 to 64 32 Manually changes the White Reference Value. 51 Accessory 0 or 1 0 0=Inhibit , 1=Enable 52 Fuser Overheat Clear 0 or 1 0 0=Clear overheat , 1=U4 Code

*Setting the Exposure Levels: Put the Exposure Lever at the center position, turn off the ‘Auto Exposure’, and select 100% magnification. Enter Diagnostic Code ‘21’. Press the ‘Start’ button, the copier will make 10 copies. Adjust the exposure during the copy cycle by pressing the ‘5’ to increase, or the ‘0’ to decrease the exposure. Repeat this process in 64% magnification & 129% magnification.
If this process doesn’t give you enough of a handle, VR1 on the Main Board (under the Upper Rear Cover) is the coarse adjustment. Set the exposure level at 32 using the procedure above. Then turn VR1 (clockwise increases exposure).

** Setting the White Level Reference Value: Enter Diagnostic Code ‘28’. Cover the entire Document Glass with plain white paper & close the Platen Cover. Press ‘Start’, the display will show ‘bb’. Select 100% and press ‘Start’. One copy will be made and the white reference Correction Value is stored in memory. The copier leaves diagnostic mode. Then go back into diagnostic mode & enter code ‘29’ followed by ‘Start’. Add 11 to the value displayed and enter that new value. Press ‘Start’ to lock in the new value.

Main PWB Dip Switch settings:

SWITCH #: 1 2 3 4 U.S.: 5312 ON OFF ON OFF 5313 ON OFF OFF OFF 5314 ON OFF OFF OFF Rank (European): 5312 OFF ON ON OFF 5313 OFF ON OFF OFF 5314 OFF ON OFF ON

Example: US 5312:

SPECIFICATIONS:
5312,5313,5314

Model#	1stCopy	Speed	Warmup	Capacity (#sheets)	Dim&wt (round up)	Power
5312	9sec.	12cpm	20sec.	250 bypass:50	20x19x12 73lbs	115v,15a
5313	9sec.	12cpm	20sec.	250 bypass:50	20x19x12 73lbs	115v,15a
5314	9sec.	12cpm	20sec.	250 bypass:50	22x23x16 80lbs	115v,15a

Suggested Retail Pricing: 5312: $2,800.- ... 5314: $3,425.-

5313 Zoom Capabilities
(Preset Reduction = 64,78%) (Preset Enlargement = 110,129%)
(Zoom Magnification = 64-129%...1% increments)
5314 Zoom Capabilities
(Preset Reduction = 64,78%) (Preset Enlargement = 129,154%)
(Zoom Magnification = 50-200%...1% increments)

Yields:
Drum Cartridge: 18,000
Toner Cartridge: 4,000 (Assumes average area coverage of 6%...Regular full page of text)

To Program your copier to your preferences:

• Press the ‘Auto’ button for about 6 seconds. The copier diagram lights will flash.
• Enter the 'Program Number' followed by ‘Start’. The current setting will be displayed (Default for all of the Programs is ‘1’).
• Enter your choice from the available Program Options and press ‘Start’. Press ‘Auto’ to exit the Programming Mode.

5312 style PARTS

TECH INFO MENU

CATALOG MENU

HOME PAGE MENU